[IEEE 2014 International Renewable and Sustainable Energy Conference (IRSEC) - Ouarzazate, Morocco (2014.10.17-2014.10.19)] 2014 International Renewable and Sustainable Energy Conference (IRSEC) - Maximum loading point in distribution system with renewable resources penetration
- 作者Guerriche, Khaled Ras; Bouktir, Tarek
- 文件大小1680.16KB
- 发表时间2014
- DOI10.1109/irsec.2014.7059767
- 页码481-486
Quantitative analysis of bubble size and electrodes gap at different dielectric conditions in powder mixed EDM processKumar, Amit; Mandal, Amitava; Dixit, Amit Rai; Mandal, Deepak Kumar · The International Journal of Advanced Manufacturing Technology · 2020
Investigation of powder mixed EDM process parameters for machining Inconel alloy using response surface methodologykumar, Amit; Kumar, Saroj; Mandal, Amitava; Rai Dixit, Amit · Materials Today: Proceedings · 2018
Parametric investigation on abrasive waterjet machining of alumina ceramic using response surface methodologyTiwari, Tanmay; Sourabh, Saket; Nag, Akash; Dixit, Amit Rai; Mandal, Amitava; Das, Alok Kumar; Mandal, Niladri; Srivastava, Ashish Kumar · IOP Conference Series: Materials Science and Engineering · 2018
Modeling and Optimization of Machining Nimonic C-263 Super Alloy Using Multi-Cut Strategy in WEDMMandal, Amitava; Dixit, Amit Rai; Das, Alok Kumar; Mandal, Niladri · Materials and Manufacturing Processes · 2015
Performance Evaluation of Al <sub/>2</sub> O <sub/>3</sub> Nano Powder Mixed Dielectric for Electric Discharge Machining of Inconel 825Kumar, Amit; Mandal, Amitava; Dixit, Amit Rai; Das, Alok Kumar · Materials and Manufacturing Processes · 2017
Influence of graphene-based nanofluid with minimum quantity lubrication on surface roughness and cutting temperature in turning operationSingh, Rabesh kumar; Sharma, Anuj Kumar; Bishwajeet, ; Mandal, Vimal; Gaurav, Kumar; Nag, Akash; Kumar, Amit; Dixit, Amit Rai; Mandal, Amitava; Kumar Das, Alok · Materials Today: Proceedings · 2018
Experimental investigation of thermal conductivity and specific heat of nanoparticles mixed cutting fluidsSingh, Rabesh Kumar; Sharma, Anuj Kumar; Dixit, Amit Rai; Mandal, Amitava; Tiwari, Arun Kumar · Materials Today: Proceedings · 2017
Offline adaptive controlKarunakaran, K.P.; Shah, Mihir; Shringi, R.; Bernard, A.; Arrazola, P.J. · International Journal of Machining and Machinability of Materials · 2010
An opening historical noteAstakhov, Viktor P. · International Journal of Machining and Machinability of Materials · 2006
Tool wear mechanisms in machiningYume, Jorge A. Olortegui; Kwon, Patrick Y. · International Journal of Machining and Machinability of Materials · 2007
Machining residual stresses and part distortionsZamashchikov, Yury I. · International Journal of Machining and Machinability of Materials · 2007
Cutting forces measurements during discontinuous machining processBenmohammed, B. · International Journal of Machining and Machinability of Materials · 2012
Metal cutting modelling SPH approachLimido, J.; Espinosa, C.; Salaun, M.; Mabru, C.; Chieragatti, R.; Lacome, J.L. · International Journal of Machining and Machinability of Materials · 2011
Optimisation of EDC parameters using TOPSIS approachSenthilkumar, C. · International Journal of Machining and Machinability of Materials · 2019
Prevention of wire breakage in wire EDMKumar, Rajnish; Choudhury, S.K. · International Journal of Machining and Machinability of Materials · 2011